Comments for fangin.com

Comment on avrdude: stk500():not in sync: resp=0x00 by Erlinda

Erlinda — Fri, 13 Mar 2020 08:32:20 +0000

Right here is the perfect site for anybody who really wants
to find out about this topic. You understand a whole lot its almost tough to
argue with you (not that I really would want
to…HaHa). You definitely put a fresh spin on a subject which has been discussed for many years.

Great stuff, just excellent!

Comment on Bad Boy v2 – Precision Aerobatics by Atle

Atle — Thu, 15 Mar 2018 18:58:40 +0000

Hello
Can you help me.
What is the CG on a precision aerobatics bad boy V2.
Best regards
Atle Rushfeldt

Comment on SC Models – Foamy Profile EDGE 540 build by Kamil

Kamil — Fri, 29 Dec 2017 19:14:24 +0000

Hi, i have tej same model. Do you have still instruction , how to build?

Kamil

Comment on rcpowers.com extra 300 foamy – electronics by Edward

Edward — Fri, 22 Dec 2017 10:52:12 +0000

How many minutes flight time do you get with that motor/prop/battery?
I use a 2200kv, 6X4, 1800mAh and get around 7 minutes to 11.1V on the battery.

Comment on Multirotor loops and rolls just got easier with OpenPilot by rodger

rodger — Wed, 05 Apr 2017 15:22:36 +0000

im using a newer version of open flight v 15.01 I think and the cruise control option as shown doest appear for me
any chance send me the version ur using? as I cannot get this darn thing flying at all

Comment on “Start message not received within 10 seconds, disconnecting” by Nienscecco

Nienscecco — Sat, 07 Jan 2017 01:34:49 +0000

After reading your post, I thought it was the solution I needed. Maybe the protocol of the chrome configurator has changed since then but it did not work for me. My solution was to simply connect the DTR pin from the serial connection. I could not connect to the module because it had no firmware in it most probably. And I could not flash a firmware in it because DTR is probably connected to the reset pin of the ATMEGA chip in the module and is needed to start flashing a new firmware image. When I connected DTR, I was able to flash the module and now I can connect directly. If I disconnect DTR, I am not able to connect to the module anymore. The DTR signal is used by the chrome configurator to reset the module at the right time at which it will send its start message (My understanding). If this can help someone else in the future…

Comment on Betaflight update to Afroflight Naze32 by ZMR250 Build – Part 1 – Parts List | fangin.com

ZMR250 Build – Part 1 – Parts List | fangin.com — Thu, 04 Feb 2016 12:59:52 +0000

[…] complete with FPV and telemetry. My experience building a previous ZMR250 has been that simple problems like outdated firmware can cause major headaches and heaps of Google searching / forum reading to find the solution. The […]

Comment on How to connect 4 ESCs to one LiPo battery (Make a power distribution board) by Ajay

Ajay — Thu, 08 Oct 2015 16:03:36 +0000

Thanks for clarify…
One another question is ..
The signal wire has 3 pins..
How to connect these 3 pins to arduino ???

Comment on How to connect 4 ESCs to one LiPo battery (Make a power distribution board) by mattmc76

mattmc76 — Thu, 08 Oct 2015 12:48:26 +0000

Correct. Three go directly to the motor. Those 3 wires are typically the same gauge wire. Of the three remaining, 1 is the signal wire typically a light gauge (say 26 AWG) wire. The remaining two go directly to the battery and should either be colour coded (red to positive, black to negative) or should be labelled with + / – symbols.

Comment on How to connect 4 ESCs to one LiPo battery (Make a power distribution board) by Ajay

Ajay — Thu, 08 Oct 2015 02:06:54 +0000

I am confuse …
ESC has Total 6 wires…
3 Directly goes in motor ..
from remaining 3 one is signal wire..
is there another remaining 2 wires are connected to bettry ??
which one is + Ve & which one is -Ve